講演抄録/キーワード |
講演名 |
2019-05-17 14:00
金属薄板の電磁圧接における放電電流転流用高速機械式スイッチの提案 ○相沢友勝(都立高専) EMD2019-2 エレソ技報アーカイブへのリンク:EMD2019-2 |
抄録 |
(和) |
この報告で,電磁圧接はコンデンサ電源から絶縁した平板状5ターンコイルへ放電電流を急激に流して行われる.間隙を設けて重ねた圧接用金属薄板をコイル上に固定し,高密度磁束を加え,薄板同士を高速衝突させて圧接する.金属薄板が衝突するとき,放電電流はほぼ最大値に達するようにする.機械式スイッチの接点用として別の金属薄板(2枚)もコイル上に置かれ,2枚の接点用薄板はそれぞれコイルの両端へ接続される.放電電流がほぼ最大値に達したとき,接点用薄板は圧接用薄板と同様に高速で衝突する.放電電流は接点用薄板を含む短絡回路へ転流する.転流後,コイルへ流れる電流は,回路条件を選ぶと振動しなくなり,徐々に減衰する.薄板の電磁圧接に使用するこのような高速機械式スイッチを提案する. |
(英) |
In this report, magnetic pulse welding is done by rapidly flowing a large discharge current from a capacitor bank to an insulated 5-turn flat coil. The overlapped welding sheet metals with a gap are fixed on the coil, and high density magnetic flux is applied to them. Both sheets collide and are welded at high speed. The current is set to be nearly peak when the welding sheets collide. Two other sheet metals for mechanical switch contacts are also placed on the coil and connected to both ends of the coil. When the discharge current reaches nearly the peak, the contact sheets collide at high speed like the welding sheets. Most of the current flowing through the coil commutates to the short-circuit including the contact sheets. Depending on the circuit conditions after the commutation, the coil current does not oscillate but gradually damps. We propose such a high-speed mechanical switch for magnetic pulse sheet-welding. |
キーワード |
(和) |
電磁圧接 / 金属薄板 / 電磁力 / コンデンサ電源 / 放電電流 / 転流 / 機械式スイッチ / |
(英) |
Magnetic pulse welding / Sheet metal / Electromagnetic force / Capacitor bank / Discharge current / Commutation / Mechanical switch / |
文献情報 |
信学技報, vol. 119, no. 41, EMD2019-2, pp. 7-11, 2019年5月. |
資料番号 |
EMD2019-2 |
発行日 |
2019-05-10 (EMD) |
ISSN |
Print edition: ISSN 0913-5685 Online edition: ISSN 2432-6380 |
著作権に ついて |
技術研究報告に掲載された論文の著作権は電子情報通信学会に帰属します.(許諾番号:10GA0019/12GB0052/13GB0056/17GB0034/18GB0034) |
PDFダウンロード |
EMD2019-2 エレソ技報アーカイブへのリンク:EMD2019-2 |