講演抄録/キーワード |
講演名 |
2012-02-08 09:30
SPMスクラッチ加工を用いた金属チャネル狭窄過程におけるコンダクタンスの量子化 ○須田隆太郎・大山隆宏・白樫淳一(東京農工大) ED2011-150 SDM2011-167 エレソ技報アーカイブへのリンク:ED2011-150 SDM2011-167 |
抄録 |
(和) |
我々は,Auチャネルに対して走査型プローブ顕微鏡(SPM)を用いたスクラッチ加工のその場コンダクタンス測定を実行し,Auチャネルの狭窄過程における量子ポイントコンタクト(QPC)の形成について検討を行った.これまで,本研究では,ダイヤモンドコーティングしたSPM探針を用いたスクラッチ加工によるナノリソグラフィーについて検討してきた。その結果,スクラッチ加工における探針の走査条件を制御することで,Siなどの比較的硬い材料に対する数十nm以下の加工痕の形成を報告してきた.本手法は直接的・物理的なナノスケール切削加工であり,金属チャネルへの適用の際には,チャネルの構造変化に伴う電気的特性の変動をIn-Situでモニターすることで,チャネルの加工状態をリアルタイムに制御することが可能となる.即ち,SPMスクラッチ加工とチャネルのその場コンダクタンス測定を組み合わせることで,加工時における素子の特性をリアルタイムに取得し,チャネル狭窄過程でのQPC形成によるコンダクタンスの量子化現象が観測できるものと期待される.今回は,大気中・室温下においてAuチャネルに対してSPMスクラッチ加工を実行し,加工中のチャネルのコンダクタンスをその場で測定することでチャネル狭窄過程における素子の電気伝導特性の変化や,形成されたQPCの安定性について検討した. |
(英) |
Quantum point contacts (QPCs) are formed by mechanically scratching Au channels with a scanning probe microscope (SPM) in ambient condition. A variation of electrical properties of the Au channels was caused by a direct modification of the channels using SPM scratching and was in-situ controlled by measuring the conductance across the scratched region. Such measurement provides a more accurate method of controlling device properties than by controlling geometry alone. Initial Au channels with width of a few micrometers were fabricated by conventional electron-beam lithography and lift-off process. Scratch experiments were carried out using a diamond-coated tip in ambient air. Then, the SPM scratching was performed across the Au channels. The electrical properties of the Au channels were measured in-situ during the SPM scratching. The conductance of the Au channel was slowly decreased with the increase of process time as the channel was constricted by the scratching. The conductance changed in quantized steps of the conductance quantum, G0 = 2e2/h at final stage of the SPM scratching. This result suggests that atomic-size contact is formed by SPM scratching. Furthermore, the conductance varies stepwise with time and exhibits clear plateaus by tuning the scan speed of the SPM tip. These results imply that SPM scratch nanolithography is promising for the fabrication of nanoscale devices consisting of QPCs. |
キーワード |
(和) |
走査型プローブ顕微鏡 / スクラッチ加工 / In-Situ測定 / 量子ポイントコンタクト / コンダクタンス量子化 / / / |
(英) |
scanning probe microscopy / scratch / in-situ measurement / quantum point contact / conductance quantization / / / |
文献情報 |
信学技報, vol. 111, no. 425, ED2011-150, pp. 47-52, 2012年2月. |
資料番号 |
ED2011-150 |
発行日 |
2012-01-31 (ED, SDM) |
ISSN |
Print edition: ISSN 0913-5685 Online edition: ISSN 2432-6380 |
著作権に ついて |
技術研究報告に掲載された論文の著作権は電子情報通信学会に帰属します.(許諾番号:10GA0019/12GB0052/13GB0056/17GB0034/18GB0034) |
PDFダウンロード |
ED2011-150 SDM2011-167 エレソ技報アーカイブへのリンク:ED2011-150 SDM2011-167 |