お知らせ 2023年度・2024年度 学生員 会費割引キャンペーン実施中です
お知らせ 技術研究報告と和文論文誌Cの同時投稿施策(掲載料1割引き)について
お知らせ 電子情報通信学会における研究会開催について
お知らせ NEW 参加費の返金について
電子情報通信学会 研究会発表申込システム
講演論文 詳細
技報閲覧サービス
[ログイン]
技報アーカイブ
 トップに戻る 前のページに戻る   [Japanese] / [English] 

講演抄録/キーワード
講演名 2009-04-24 14:55
ESDガンのグラウンドへの接触放電に対する放電電流の推定
戸谷史彦高 義礼藤原 修名工大)・石上 忍山中幸雄NICTEMCJ2009-5
抄録 (和) IEC(国際電気標準会議)では,人体ESDを模擬した耐性試験法(IEC61000-4-2)において,静電気試験器(ESDガン)の接触放電に対する放電電流波形を規定し,伝達インピーダンスを1とした電流検出変換器(以後ターゲット)への波形校正を要求している.しかしながら,ESDガンのターゲットへの注入電流が,そのまま実際の試験機器(EUT)に放電されるとは限らない.本研究では,ESDガンのEUT筐体への接触放電に対する放電電流波形が筐体サイズとの関係においてターゲットへのそれとどの程度異なるかを検討した.まず,ESDガンのターゲットへの接触放電に対する放電電流波形はESDガンの先端電極近傍に配置した磁界プローブの出力電圧波形から推定できることを確認し,つぎに,EUT筐体を模したグラウンド板(1.5 m × 1.5 m)と3種類の金属円板(直径:80, 50, 30 mm),実際のEUTとしてバッテリー駆動のラップトップ PC(B5サイズ)表面カバーの金属円環(内径:44mm,外径:52mm)への接触放電に対する放電電流波形をそれぞれ推定した.その結果,グラウンド板への放電電流の推定波形はターゲットへの放電電流の測定波形と一致すること,金属円板に対しては放電電流の立ち上がり波形は円板サイズに拘わらずターゲットへの放電電流波形に類似するものの,立ち下がり波形は全般に低く,電流ピークも小さいが,それは円板サイズと共に上昇し,直径30mmで85%,80mmではほぼ100%に達していること,ラップトップ PCでは接触放電の金属サイズが小さいにも拘わらず,放電電流波形は意外にもターゲットへのそれと概ね同じであること,などがわかった. 
(英) International Electrotechnical Commission (IEC) prescribes an immunity test (IEC61000-4-2) of electronic equipment for electrostatic discharges (ESDs), and specified the waveform of a discharge current from human ESD, which shall be calibrated for contact discharges of an ESD-gun onto an IEC recommended calibration target with a transfer impedance of 1. For the specified current waveform, however, it cannot always be injected onto actual equipment under test (EUT). In the present study, we investigated to what extent discharge currents injected onto EUT differ from the calibration target current with respect to the metallic size of EUT enclosure. We first confirmed that measured discharge currents for contact discharges of an ESD-gun onto the calibration target can be calculated from the magnetic near field simultaneously measured with a magnetic field probe placed closed to the ESD-gun, and thereby estimated the discharge currents for contact discharges onto a ground plane (1.5m by 1.5m) and circular metal plates with different diameters: 80mm, 50mm and 30mm in lieu of EUT metallic enclosures, and a metal ring (inner diameter: 44mm and outer diameter: 52mm) on the top cover of a battery-driven laptop computer (B5 size) as actual EUT. As a result, we found that the estimated discharge current onto the ground agrees with the target current, and the discharge currents onto the circular metal plates have waveforms with the same rising parts but smaller peaks, which increase with the metal size, reaching 85% and 97% for 30mm and 80mm diameters, respectively. For the laptop computer, it was found, on the other hand, that the discharge current onto a metal ring of the top cover despite small metal size for contact discharges approximately agrees with the target current.
キーワード (和) ESDガン / 電流検出変換器 / グラウンド / 放電電流 / 近傍磁界 / 電流推定 / /  
(英) ESD-gun / IEC calibration target / ground / discharge current / magnetic near field / current estimation / /  
文献情報 信学技報, vol. 109, no. 18, EMCJ2009-5, pp. 25-29, 2009年4月.
資料番号 EMCJ2009-5 
発行日 2009-04-17 (EMCJ) 
ISSN Print edition: ISSN 0913-5685    Online edition: ISSN 2432-6380
著作権に
ついて
技術研究報告に掲載された論文の著作権は電子情報通信学会に帰属します.(許諾番号:10GA0019/12GB0052/13GB0056/17GB0034/18GB0034)
PDFダウンロード EMCJ2009-5

研究会情報
研究会 EMCJ  
開催期間 2009-04-24 - 2009-04-24 
開催地(和) 岡山大学 
開催地(英)  
テーマ(和) 対策/一般 
テーマ(英)  
講演論文情報の詳細
申込み研究会 EMCJ 
会議コード 2009-04-EMCJ 
本文の言語 日本語 
タイトル(和) ESDガンのグラウンドへの接触放電に対する放電電流の推定 
サブタイトル(和)  
タイトル(英) Estimation of Discharge Currents Injected onto Ground for Contact Discharge from ESD-Gun 
サブタイトル(英)  
キーワード(1)(和/英) ESDガン / ESD-gun  
キーワード(2)(和/英) 電流検出変換器 / IEC calibration target  
キーワード(3)(和/英) グラウンド / ground  
キーワード(4)(和/英) 放電電流 / discharge current  
キーワード(5)(和/英) 近傍磁界 / magnetic near field  
キーワード(6)(和/英) 電流推定 / current estimation  
キーワード(7)(和/英) /  
キーワード(8)(和/英) /  
第1著者 氏名(和/英/ヨミ) 戸谷 史彦 / Fumihiko Toya / トヤ フミヒコ
第1著者 所属(和/英) 名古屋工業大学 (略称: 名工大)
Nagoya Institute of Technology (略称: Nagoya Inst. of Tech.)
第2著者 氏名(和/英/ヨミ) 高 義礼 / Yoshinori Taka / タカ ヨシノリ
第2著者 所属(和/英) 名古屋工業大学 (略称: 名工大)
Nagoya Institute of Technology (略称: Nagoya Inst. of Tech.)
第3著者 氏名(和/英/ヨミ) 藤原 修 / Osamu Fujiwara / フジワラ オサム
第3著者 所属(和/英) 名古屋工業大学 (略称: 名工大)
Nagoya Institute of Technology (略称: Nagoya Inst. of Tech.)
第4著者 氏名(和/英/ヨミ) 石上 忍 / Shinobu Ishigami / イシガミ シノブ
第4著者 所属(和/英) 情報通信研究機構 (略称: NICT)
National Institute of Information and Communications Technology (略称: NICT)
第5著者 氏名(和/英/ヨミ) 山中 幸雄 / Yukio Yamanaka / ヤマナカ ユキオ
第5著者 所属(和/英) 情報通信研究機構 (略称: NICT)
National Institute of Information and Communications Technology (略称: NICT)
第6著者 氏名(和/英/ヨミ) / /
第6著者 所属(和/英) (略称: )
(略称: )
第7著者 氏名(和/英/ヨミ) / /
第7著者 所属(和/英) (略称: )
(略称: )
第8著者 氏名(和/英/ヨミ) / /
第8著者 所属(和/英) (略称: )
(略称: )
第9著者 氏名(和/英/ヨミ) / /
第9著者 所属(和/英) (略称: )
(略称: )
第10著者 氏名(和/英/ヨミ) / /
第10著者 所属(和/英) (略称: )
(略称: )
第11著者 氏名(和/英/ヨミ) / /
第11著者 所属(和/英) (略称: )
(略称: )
第12著者 氏名(和/英/ヨミ) / /
第12著者 所属(和/英) (略称: )
(略称: )
第13著者 氏名(和/英/ヨミ) / /
第13著者 所属(和/英) (略称: )
(略称: )
第14著者 氏名(和/英/ヨミ) / /
第14著者 所属(和/英) (略称: )
(略称: )
第15著者 氏名(和/英/ヨミ) / /
第15著者 所属(和/英) (略称: )
(略称: )
第16著者 氏名(和/英/ヨミ) / /
第16著者 所属(和/英) (略称: )
(略称: )
第17著者 氏名(和/英/ヨミ) / /
第17著者 所属(和/英) (略称: )
(略称: )
第18著者 氏名(和/英/ヨミ) / /
第18著者 所属(和/英) (略称: )
(略称: )
第19著者 氏名(和/英/ヨミ) / /
第19著者 所属(和/英) (略称: )
(略称: )
第20著者 氏名(和/英/ヨミ) / /
第20著者 所属(和/英) (略称: )
(略称: )
講演者 第1著者 
発表日時 2009-04-24 14:55:00 
発表時間 25分 
申込先研究会 EMCJ 
資料番号 EMCJ2009-5 
巻番号(vol) vol.109 
号番号(no) no.18 
ページ範囲 pp.25-29 
ページ数
発行日 2009-04-17 (EMCJ) 


[研究会発表申込システムのトップページに戻る]

[電子情報通信学会ホームページ]


IEICE / 電子情報通信学会