講演抄録/キーワード |
講演名 |
2009-02-24 15:15
20kHzの超音波複合振動を用いた金属ピン等の押し込み固定加工 ○辻野次郎丸・上岡哲宜(神奈川大)・杉本榮一(アサヒ・イー・エム・エス) US2008-99 |
抄録 |
(和) |
金属ピン・軸等の押し込み加工時に20 kHzの超音波振動を静加工力に重畳して押し込み固定加工を行う超音波振動押し込み固定加工について検討した。金属ピン、中心軸等の固定には押し込み穴部の加熱または押し込みピンを低温状態で押し込み加工を行うか、または静圧力を印加して押し込み固定加工を行っている。静圧力のみでの押し込み加工では加工力が大なため固定側の軸受け台座等が破損する、また固定力が減少する、更に中心軸が偏芯し補正が必要である等の欠点がある。押し込み加工時に超音波振動を静圧力に重畳させて押し込み加工を行うことにより押し込みに必要な静加工力が減少する。このため製品の破損が減少し、固定軸等の偏芯が改善される。する場合の必要加工力、保持力、ピンまたは穴部の粗さ等について検討した結果、通常のプラスチック溶接用の振動装置では押し込み力が減少し、金属ピンまたは穴部の表面粗さが減少するが、金属ピンを押し出すのに必要な固定力も減少する。大容量の超音波振動装置を用いて検討した結果、比較的低速押し込み加工では固定力が減少するが、高速・大振動振幅で押し込み加工を行うことにより局部的な溶接が行われ固定力が増加し、また偏芯量も減少する事が明らかになった。 |
(英) |
Plunging of metal pin or shaft was studied inducing 20 kHz longitudinal vibration on static plunging force during plunging process. When inserting pin or shaft using only static force, the material with holes happen to broken by plunging pin by large static force and also the motor shaft plunged into the rotor center has inevitably eccentricity and must to adjust the eccentricity by manual or using some machines. Using ultrasonic vibration, static force and eccentricity the pin and shaft can be decreased due to decreasing frictional force by ultrasonic vibration. Using a 20 kHz large capacity vibration system, holding force is rather small under low speed plunging but become larger under high speed plunging and large vibration amplitude about 20 mm(peak-to-zero value). Require static plunging forces were larger under high speed plunging. |
キーワード |
(和) |
押し込み加工によるピンの固定 / 超音波振動によるピンの押し込み固定加工 / 超音波振動による押し込み力の減少 / ピンの保持力 / 振動振幅 / 押し込み速度 / 表面粗さ / 偏芯の改善 |
(英) |
Fixing of Pins by Plunging / Plunging of Pins Using Ultrasonic Vibration / Decreaseing of Plunging Force by Vibration / Holding Force of Pins / Vibration Amplitude / Plunging Speed / Surface Roughness / Improvement of Eccentricity |
文献情報 |
信学技報, vol. 108, no. 436, US2008-99, pp. 35-40, 2009年2月. |
資料番号 |
US2008-99 |
発行日 |
2009-02-17 (US) |
ISSN |
Print edition: ISSN 0913-5685 Online edition: ISSN 2432-6380 |
著作権に ついて |
技術研究報告に掲載された論文の著作権は電子情報通信学会に帰属します.(許諾番号:10GA0019/12GB0052/13GB0056/17GB0034/18GB0034) |
PDFダウンロード |
US2008-99 |