講演抄録/キーワード |
講演名 |
2017-10-28 10:45
単結晶アシスト及び2段階焼成によるニオブ酸リチウムセラミックスの作製 高宮 開・横山裕紀・小笠原 孝・高須敬士・○番場教子(信州大) CPM2017-76 エレソ技報アーカイブへのリンク:CPM2017-76 |
抄録 |
(和) |
本研究では難焼結性のニオブ酸リチウム(LN)セラミックスの緻密体を作製するために,LN単結晶及び2段階焼成プロセスを用いた.成形体をLN単結晶板で挟んで2段階焼成することで,急激な粒成長を抑制でき,焼結助剤や固溶無しのLN単相で約95%の相対密度をもつLNセラミックスが得られた.またLN単結晶で成形体を挟んで焼成した場合,単結晶無しで作製したセラミックに比べ焼結が進み,緻密化及び粒成長が促進されることを確認した.LN単結晶より重い酸化アルミニウム板を載せて焼成した試料の密度及び平均粒径が単結晶無しで作製したLNセラミックとほぼ同じであったことから,LN単結晶の重量効果ではなく,単結晶により粉末の焼結が促進されたことがわかった. |
(英) |
In this research, lithium niobate (LN) single crystal and a two-step firing process were used to obtain dense LN ceramics which is material with low sinterability. The effects of the two-step firing process and single crystal on sintering of LN were investigated. LN single phase ceramics with a relative density of about 95% can be obtained without sintering aid and solid solution. This is due to that normal grain growth occurred in the 1st step of the two-step firing process suppressed a rapid grain growth in the subsequent 2nd step at higher temperature. It was confirmed that grain growth and densification were promoted when ceramics were sandwiched between LN single crystals during sintering, compared to ceramics prepared without single crystals. Promotion of sintering by LN single crystals is concluded from the fact that the density and average grain size of LN ceramics sintered by using a heavier Al2O3 plate were almost the same as LN ceramics without single crystals. |
キーワード |
(和) |
ニオブ酸リチウム / セラミックス / 2段階焼成 / 単結晶アシスト / / / / |
(英) |
lithium niobate / ceramics / two-step firing / single crystal assist / / / / |
文献情報 |
信学技報, vol. 117, no. 268, CPM2017-76, pp. 51-55, 2017年10月. |
資料番号 |
CPM2017-76 |
発行日 |
2017-10-20 (CPM) |
ISSN |
Print edition: ISSN 0913-5685 Online edition: ISSN 2432-6380 |
著作権に ついて |
技術研究報告に掲載された論文の著作権は電子情報通信学会に帰属します.(許諾番号:10GA0019/12GB0052/13GB0056/17GB0034/18GB0034) |
PDFダウンロード |
CPM2017-76 エレソ技報アーカイブへのリンク:CPM2017-76 |